(888) ipd-converters (888) 473-2668 www.ipdconverters.com c-10 ias010yg 40 45 50 55 60 65 70 75 80 85 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. (18v) eff. (24v) eff. (36v) setpoint accuracy 1% line regulation v in min. - v in max., i out rated 0.2% v out load regulation i out min. - i out max., v in nom. 0.5% v out minimum output current 10 % i out rated dynamic regulation, loadstep 25% i out pk deviation 4% v out settling time 500 s voltage trim range 10% short circuit / overcurrent protection shutdown / hiccup current limit threshold range, % of i out rated 110 - 140% technical specifications ias dc/dc converters provide up to 12 watts of output power in an industry standard package and footprint. with a maximum case temperature of 100c, the ias is well suited for the most demanding applications. the ias features 1500 vdc isolation, short circuit, and overtemperature protection, as well as six-sided shielding. the ias is available with optional enable and voltage trim. please see the iad series for dual output applications. industry standard package industry standard footprint up to 12w output 100c case operation optional trim and enable wide range input 1500v isolation short circuit protection description fea tures ias series - 12 watt efficiency vs. load (24v input) turn-on time 10 ms remote shutdown positive logic switching frequency 375 khz isolation input - output 1500 vdc input - case (24 v in ) 1050 vdc output - case (48 v in ) 500 vdc temperature coefficient 0.03%/c case temperature operating range -40 to +100c storage range -55 to +115c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 5 g, 10 - 55 hz mtbf ? (bellcore tr-nwt-000332) 2.1 x 10 6 hrs safety ul, cul, vde weight (approx.) 1.0 oz general notes ? mtbf predictions may vary slightly from model to model. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260 c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. voltage range 24 vdc nominal 18 - 36 vdc 48 vdc nominal 34 - 75 vdc reflected ripple 25 ma input reverse input current shunt diode input output
c-11 thermal impedance tolerances note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. pin function ias series - 12 watt 1+v in 2-v in 3no pin (shutdown) 4+v out 5no pin (trim) 6-v out natural convection 15.4 c/w 100 lfm 12.2 c/w 200 lfm 9.3 c/w 300 lfm 7.4 c/w 400 lfm 6.4 c/w inches: (m illimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 case: + 0.04, - 0.00 + 1.0, - 0.00 ( dimensions as listed unless otherwise specified.) mechanical drawing vin (volts) vin range (volts) iin max.* (amps) vout (volts) iout rated (amps) ripple & noise pk-pk (mv) efficiency typ. ** model 24 24 24 24 48 48 48 48 18 - 36 18 - 36 18 - 36 18 - 36 34 - 75 34 - 75 34 - 75 34 - 75 0.49 0.69 0.81 0.79 0.26 0.36 0.43 0.43 3.3 5 12 15 3.3 5 12 15 2.0 2.0 1.0 0.8 2.0 2.0 1.0 0.8 75 75 120 150 75 75 120 150 75% 80% 85% 86% 75% 81% 85% 86% ias006ye ? ias010yg ias012yh ias012yj ias006ze ias010zg ias012zh ias012zj ? denotes advanced product release. consult factory for product availability. * maximum input current at minimum input voltage, maximum rated output power. ** at nominal vin, rated output.. models - (see the last page of this file for options.) (1.0mm) dia 0.040" (4.6mm) 0.18" min. (10.7mm) 0.42" 1.00" (50.8mm) 2.00" 0 1.40"(35.6mm) 0.800"(20.3mm) (25.4mm) bottom view 56 2 1 3 4 0 (22.9mm) 0.900" (20.3mm) 0.800" (12.7mm) 0.500" (10.2mm) 0.400" (7.6mm) 0.300"
c105 options when ordering equipment options, use the following suffix information. select the option(s) that you prefer and add them to the model number. example ordering options are located below the options table. option suffix applicable series remarks negative logic n has, hbd, hbs, hes, les, qbs, qes, tes, tqd ttl ?low? turns module on ttl ?high? turns module off lucent compatible trim t has, hbd, hbs, hes, qbs, qes t e r m i nal s t r i p t s x w s , xwd, xwt trim 1 ias, les enable 2 iad, ias, les, sms trim and enable 3 ias, les current share 4 sms headerless y encapsulated ews, iws, ows pin length and heatsink options standard pin length is 0.180? (4.6mm) 0.110? (2.8mm) pin length 8 all units (except sms) 0.150? (3.8mm) pin length 9 all units (except sms) 0.24? (6.1mm) horizontal heatsink 1h all units (except dip, sip, and sm packages) includes thermal pad 0.24? (6.1mm) vertical heatsink 1v all units (except dip, sip, and sm packages) includes thermal pad 0.45? (11.4mm) horizontal heatsink 2h all units (except dip, sip, and sm packages) includes thermal pad 0.45? (11.4mm) vertical heatsink 2v all units (except dip, sip, and sm packages) includes thermal pad 0.95? (24.1mm) horizontal heatsink 3h all units (except dip, sip, and sm packages) includes thermal pad 0.95? (24.1mm) vertical heatsink 3v all units (except dip, sip, and sm packages) includes thermal pad example options:hbs050zg-ant3v = hbs050zg-a with negative logic, lucent compatible trim, and 0.95? vertical heatsink. les015yj-3n = les015yj with optional trim and enable, negative logic. qbs066zg-at8 = qbs066zg-a with lucent compatible trim and 0.110? pin length. nuclear and medical applications power-one products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the president of power-one, inc. technical revisions the appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. specifications are subject to change without notice.
|
